Aluminum & Wrought Iron in Edmond, OK

Ornamental metal is vertical pickets on horizontal rails, anchored by metal posts in concrete — an open design that trades solid privacy for sight lines, security, and near-zero wind load. Aluminum arrives as prefabricated panels, commonly 6–8 feet wide in heights from 36 to 72 inches, bracket-mounted to posts; wrought iron follows the same structure with custom fabrication and welding. In a state where solid fences act as sails, this category is the structural winner: strong posts and rails paired with pickets that let the wind pass straight through.

That combination is why ornamental metal keeps showing up in the two places Edmond rules are strictest — front yards and pool enclosures.

Aluminum splits into residential, upgraded, and specialty lines, and the differences are real. Standard residential panels run roughly $69–$182 each with posts at $25–$44, working out to materials in the mid-teens to mid-twenties per linear foot depending on height and style. Upgraded lines run about $24–$35.50 per foot in materials. "Puppy" or XP styles tighten the lower pickets for pet containment at roughly $25–$37.66 per foot. The premium tier is privacy and semi-privacy aluminum with horizontal slats — panels from $284 to $636, materials at $63–$113 per foot. Wrought iron installs at roughly $30–$50 per foot for 4-foot heights and $60–$100 for 6-foot security fencing.

Edmond's city code sets no front-yard fence height cap — that is an OKC-style rule Edmond never adopted — so short, open front fencing is an HOA convention here, and open picket or wrought iron is exactly what most covenants ask for. The one citywide front-yard rule is the corner-lot sight triangle: nothing between 3 and 7 feet tall may sit in the 25-foot visibility triangle at an intersection. Pool enclosures are stricter, and the City of Edmond's barrier standards are specific: a minimum 48-inch barrier height, no opening that passes a 4-inch sphere, member-spacing rules, and self-closing, self-latching gates that open away from the pool with the latch release at least 54 inches up (EMC 16.06.535). Violations draw fines of up to $200 per day, with each day a separate offense. We build pool fences to that checklist and stand with you at inspection.

When we build a pool fence, we build it against the city's pool barrier checklist, based on the 2015 ISPSC — and the details are exact. The barrier must stand at least 48 inches, measured on the outside of the fence, not the pool side. The gap under the barrier can be no more than 2 inches at grade, or 4 inches only where the barrier mounts on the pool structure itself. No opening anywhere may pass a 4-inch sphere. Horizontal members closer than 45 inches apart must face the pool side, with vertical picket spacing under 1.75 inches — the rule that keeps the fence from doubling as a ladder. Even chain link is addressed: mesh openings cap at 2.25 inches square unless slats bring them to 1.75 inches or tighter. These are not design suggestions; they are the pass-fail lines the inspector checks, so we design the panel spec to them before anything is ordered.

Edmond's barrier requirement is triggered by water, not by the word pool: anything holding water deeper than 24 inches — in-ground pools, aboveground pools, hot tubs, and spas — must be fully enclosed. If a wall of your house forms part of the enclosure, the doors in that wall need alarms, or the pool needs a power safety cover meeting ASTM 1346. And the timing is enforced: the barrier is inspected before the pool can legally be occupied, and using a pool ahead of final inspection and the Certificate of Occupancy draws fines of up to $200 per day, with each day counted as a separate offense. We build to the checklist, schedule the inspection, and stand there with you when the inspector walks the line — because a barrier that fails costs you a re-inspection and a chunk of your summer.

Labor for aluminum averages $10–$40 per linear foot, and typical complete projects run $3,000–$8,500 including gates. Standard picket aluminum generally prices at or below wrought iron at comparable heights, and it never rusts — aluminum is naturally corrosion-resistant, while iron needs periodic refinishing at welds and cut ends to stop rust. Iron buys you heft, true custom fabrication, and a presence aluminum approximates but does not match. Both sit above wood and vinyl up front and pay it back in lifespan and low upkeep.

Edmond fence demand peaks in March, and pool-barrier work is a big reason: pool projects kick off in spring so the water is ready by summer, and every one of them needs a code-compliant barrier before the city signs off. That timing creates a squeeze. The same spring weeks bring storm-season repair demand, so crews and inspection calendars fill fast — and a pool waiting on its barrier inspection is a pool nobody is allowed to swim in. Our advice for pool owners is simple: get the fence designed and scheduled in late winter, while the December-through-February slowdown keeps lead times short, so the barrier is up and inspected before the pool contractor finishes. September brings a second demand peak for fence work generally, but for pools the calendar only runs one direction — toward the first hot weekend.

Residential ornamental gates run 36–60 inches wide, up to 72 in some configurations, and gate posts get larger sizing or deeper embedment than line posts because they carry both the panel's weight and the load of every swing. If you have small dogs, ask about puppy-picket panels before the order goes in — the tighter lower picket spacing is a factory configuration, not a retrofit. Panel-to-post brackets, rail counts, and picket spacing all vary between the residential and upgraded lines, and on pool enclosures those spacing numbers stop being aesthetic choices and become code items. We walk the line item by item at the estimate so the fence that arrives is the fence that passes inspection.

If the goal is affordable full privacy, this is not your fence. Open pickets screen nothing, and slatted privacy aluminum at $63–$113 per foot in materials costs more than good wood or vinyl privacy. Some HOAs mandate wood or vinyl uniformity on rear lines, which rules metal out regardless of preference. And for hard-security commercial sites, standard ornamental lines are not the answer either — anti-cut, anti-climb systems or welded panels do that job. Even with wind-friendly open panels, posts still get the full Oklahoma treatment: one-third of length below grade with widened footings, because clay movement does not care what the panels look like.